Sunday, 9 November 2014

Test Equipment used in Optical fiber maintenance

Testing Parameters in Optical Network

Following are the testing parameters used in optical network.

Trans optical power
•Receive optical power
•OSNR
•Dispersion (Read about dispersion here)
•Wavelength
•Wavelength deviation
•Fiber loss (Read about Fiber loss here)
•Connector loss
•Splicing loss

Optical Power Meter (OPM)


•OPM measure the average optical power out of an optical fiber.
•Power meters are calibrated at the typical wavelengths used in fiber optics, 850, 1300 and 1550 nm.
•Some meter uses Auto wavelengths Recognition feature.



Optical Light Source(OLS)


•OLS along with Optical Power Meter is used to make measurements of optical loss or attenuation in fibers and connectors.
•It should be compatible with the type of fiber in use (singlemode or multimode with the proper core diameter) and the wavelength.
•Sources may be either LED's or LASERS.
•Sometimes optical power meters are combined with an Optical Light Source (OLS) or Visual Fault Locator (VFL).




OTDR


•Optical Time Domain Reflectometer (OTDR) is used for estimating the fiber’s length and overall attenuation, including splice and mated-connector losses and to locate faults, such as breaks.
•OTDR functions by injecting a series of optical pulses into the fiber under test, using LASER.
•It requires access to only one end of the fiber.

Fiber Trace at OTDR





Optical Spectrum Analyzer (OSA)


•Optical signal monitoring on live channels.
•Able to analyze
–Optical Power
–Optical wavelength
–OSNR of each wavelength
–Spectral width of optical source



Visual Fault Locator


•Visual Fault Locator is used to inject the visible light to visually trace fiber.
•It covers the range where OTDRs are not useful.
•This is used for buffered fiber and even jacketed single fiber cable if the jacket is not opaque to the visible light.




Monday, 3 November 2014

Dispersion in Optical Fiber / Notes on Dispersion

Dispersion in Optical Fiber


Various wavelengths of the signal have different propagation velocities. Dispersion is the spreading out of a light pulse in time as it propagates down the fiber. Dispersion limits the information carrying capacity of a fiber. It is measured as ps/nm.km



Types of Dispersion

–Intermodal dispersion
–Material dispersion
–Waveguide dispersion.
( Also read about losses in optical fiber )

Intermodal Dispersion:


•Each mode enters the fiber at a different angle, take different path, travel different distance and arrive at different time at the fiber output.
•Multimode fibers have many different light modes since they have much larger core size.
•The light pulse spreads out in time which can cause signal overlapping.

Material Dispersion


•Dependence of refractive index of the material on wavelength.
•The velocity of light through a fiber depends on its wavelength.
•Different wavelengths travel at different velocity due to refractive index, hence the different propagation causes material dispersion.
•Material dispersion at 1300nm for silica is zero.

Waveguide Dispersion


•Distribution of light between core and cladding is a function of the wavelength travelling in waveguide.
•Light ray that travels in the cladding travels faster than that in the core causes waveguide dispersion.
•Single mode fiber suffers from waveguide dispersion as it has small core diameter

Chromatic Dispersion


•Combined effect of Material and Waveguide Dispersion

Polarization Mode Dispersion (PMD)


•Asymmetry, due to Mechanical and thermal stresses during fiber manufacturing introduces small index of refraction differences for the two polarization states.
•Polarization Mode Dispersion (PMD) a form of modal dispersion, causes broadening of the input pulse due to a phase delay between input polarization states.

Effect of Dispersion


•Spreading of pulses which can cause Inter Symbol Interference ‘ISI.
•Detection of individual pulse is not easy at receiver.
•Poor BER performance.
•Limit the communication distance.
•Limit the transmission rate.